Current lead times are located under MORE > TERMS AND CONDITIONS. If you would like to put down a 25% deposit rather than pay in full to get on the build schedule, please reach out for a custom invoice. Remainder due once the bumper is built and ready to ship.
Introducing our take on a high clearance rear bumper designed for the 5th gen 4runner! It features unmatched looks, strength, and has more clearance than any other bumper on the market. By removing the rear crossmember and factory tow hitch, you are gaining nearly 9 inches of clearance at the rear end for a substantial increase in departure angle.
Aside from the aggressive style and low profile fitment, it was carefully engineered with materials to take a beating while keeping weight to a minimum. The base bumper weighs in at only 80 lbs with hardware! Once you add the full width swingout with tire carrier, accessory mounting panel, and fold down aluminum camp table it brings the total weight to around 135 lbs with hardware.
One of the more interesting features of this bumper is that it doesn’t fit just one model or trim level, but several. With countless hours of engineering, the bumper has been designed to fit not just the 5th gen 4runner, but also the 4th gen 4runner, Lexus GX470, and Lexus GX460! How is that possible you ask? The key was removing the rear crossmember. Once that's out of the picture you are left with nearly identical frame rails. Unfortunately the factory mounting points on the bottom of the frame rails aren’t exactly the same between models but are close, so those are bolted down through large slots on the base plates of the bumper. You can then move the bumper forward or backwards slightly to get your preferred fitment. You then mark and drill a set of holes straight up through the frame rails to be concentric with nuts welded to a bracket on the bumper that rests on the top side of the frame. Large m12 grade 8 bolts are passed through the holes and are used to lock the bumper in place from moving forward or backward. Because of the dual shear mounting brackets sandwiching the frame, it gives back much of the strength that was taken away by cutting out the crossmember.
A few other notable features:
Includes welded tabs for mounting pod lights. Recommended for use with either Baja Designs S2’s or Diode Dynamics SSC2’s. Other similar sized cheaper lights may also work. You may have to use different mounting hardware.
- Swingout has three different locking locations with standard spindle. 1st, locks when closed. 2nd, locks at 95 degrees. 3rd, locks at 120 degrees. In the 3rd position, the swingout and hatch won't interfere when open.
- Optional Ratha Designs dual shear HD hinge upgrade allows for a stronger hinge to run larger spares/more gear weight. Locks when closed, at 90 degrees, and at 120 degrees.
- Accessories panel features hole patterns compatible with RotoPax mounts.
- Tire carrier with standard spindle is designed for use with spares up to 35”. Up to 37" with Ratha hinge.
Wheel mount on the tire carrier has multiple mounting locations and can be raised or lowered.
Aluminum camp table has built-in bottle openers.
It is reccomended for the swingout to be built with the spindle and tire carrier on the right/passenger side. This helps level out the rear and correct any lean caused by the gas tank on the drivers side.
All mounting hardware is grade 8 or stronger.
Recovery points are 1/2" thick and pass through to the inside of the bumper. Welded both inside and out.
License plate relocation mounting holes on swingout.
Pricing:
Base bumper with built in receiver. $1250
Full width swingout with tire carrier and wheel mount. +$900
Accessory mounting panel add-on for swingout. +$125
Fold down aluminum camp table add-on for swingout. +$225
Add extra 2" receiver to swingout for bike rack. +$60
Ratha HD dual shear hinge upgrade for swingout. +$100
Swingout Direction:
- Left / driver side (hinge on driver side and latch on passenger side).
- Right / passenger side (hinge on passenger side and latch on driver side).
READ BEFORE YOU ORDER:
NO TOW RATING! INTENDED FOR OFF-ROAD USE ONLY.
HIGH CLEARANCE VERSION REQUIRES CUTTING AND REMOVAL OF THE REAR FRAME CROSSMEMBER.
REQUIRES FREIGHT SHIPPING.
FLAT RATE SHIPPING: The average cost to ship this bumper (and any add-ons) within the lower 48 is $350. See more details under the SHIPPING INFO tab.
REQUIRES ADDITIONAL HOLES DRILLED THROUGH FRAME RAILS FOR MOUNTING.
CUTTING OF PLASTIC BUMPER COVER IS REQUIRED.
WILL NOT WORK WITH SPARE IN FACTORY LOCATION.
No guarantee on the swingout working with hatch mounted ladders.
- Requires sensors in rear bumper cover to be removed.
- Swingout options will partially/fully block rearview camera.
Designed for stock body height and suspension lifted vehicles only. Having a body lift will result in a different fitment than pictured. You will need to cut the plastic cover at a different height.
Depending on wheel offset, you may have to run spacers in order to prevent the sides of the tire from hitting the swingout.
Swingout can NOT be added to the bumper later on. Must be purchased at the same time.
Max recommended tire size is 35”.
If ordering with an extra receiver on swingout, the receiver will be offset to the latch side in order to leave room for your spare tire. Max tire size with this option is 35".
When running the swingout with a spare or extra weight from gear, you may experience a slight shake or bounce when hitting repetitive bumps.
When running the swingout with a spare, the factory license location will be partially covered. You will need to relocate your license plate.
The bumper is only shipped as raw steel. There may be evidence of anti-spatter spray, oils, areas with light surface rust, small amounts of weld splatter, and shallow scratches caused during manufacturing and/or shipping.
Powdercoating is only available if doing local pickup. If you would like to add, please reach out for a custom invoice.
Once again, THE RECEIVER IS NOT RATED!!! It was designed to be as strong as possible and comparable to the oem capacity, but LEGALLY WE CAN'T GIVE IT A RATING. It is intended for offroad use only and towing a trailer or carrying any hitch mounted accessories on public highways is at your own risk and the user takes all liability. We can not provide any insight or recommendations as to what you can safely tow. Use your best judgment.
IT IS HIGHLY RECOMMENDED TO READ THE INSTALL INSTRUCTIONS BEFORE ORDERING.
2010+ 4RUNNER HIGH CLEARANCE REAR BUMPER
This bumper ships freight! It will be palletized and delivered to the freight terminal closest to your location for you to pickup. You will receive tracking information once it ship. Once it arrives at your local terminal you will be contacted to schedule pickup.
Flat Rate: The average cost to ship this bumper (and any add-ons) within the lower 48 is $350.
Local Pickup: If you are local to Stillwater, MN or are willing to make the drive you are welcome to pick up your order from our shop for free. Once your order is ready you will be contacted to schedule a time to pick up.
If you are outside the lower 48 and would like to order, please reach out for a shipping quote and invoice.